Open 24/7, weekends & holidays
IDA Certified Residential & Commercial
Garage Door Remotes, Keypads & Sensors in Maryland
Fast Service. Fair Pricing. Great Warranty.
- Same-day service available
- A firm price before any work begins
- Fixed in one trip with fully stocked trucks
- Maryland licensed, MHIC #138235
Prefer to text? Text us at (410) 600-1031
Garage door not working?
$45 service call
Diagnose a problem (waived with service).
Book Your Appointment Or call (410) 600-1031Garage door remote programming and sensor repair
Garage door remote programming links a remote, keypad or car (HomeLink) to your opener, usually by pressing the opener’s learn or program button and then the remote button within 30 seconds. Garage door sensor repair fixes the two safety sensors (photo eyes) near the floor: when they are blocked, out of line or miswired, the door will not close. ADP Garage Door Repair programs remotes and keypads and aligns, rewires and replaces sensors on LiftMaster, Chamberlain, Genie and other openers across Central Maryland, 24/7, with a firm price before any work begins. The $45 service call is waived when we do the repair.
Most calls about garage door remote programming come after a move, a lost remote, a new car or a new opener; most sensor calls start with a door that goes down, stops and goes back up. Below: what the sensor lights mean, how to align them, a short guide to programming remotes, keypads and cars, and when to call us. The steps follow LiftMaster and Chamberlain support, Genie’s manuals, and the federal safety rules published by the CPSC.
- 1993 since then, federal rules require photo eyes or an equivalent sensor on new openers
Garage door safety sensors blinking: what the lights mean
The sensors sit on both sides of the door opening, near the floor, facing each other. One sends an invisible beam and the other receives it. If anything crosses the beam while the door is closing, the opener stops and reverses the door.
| What you see | What it means | What to try |
|---|---|---|
| LiftMaster and Chamberlain (amber light sends, green light receives) | ||
| Both lights steady | Normal: the beam is clear | Nothing |
| Amber steady, green off or flickering | The beam is blocked or the sensors are out of line; sometimes a wire problem | Clear the beam, wipe the lenses, align the green sensor (steps below) |
| Both lights off | The sensors have no power | Check the sensor wires at the back of the opener; look for a cut or stapled wire |
| Opener lights flash 10 times, door reverses | The opener is reporting a sensor problem (openers and logic boards made after 2022 no longer flash this way) | Check the sensors; see LiftMaster codes for code 1-1 and 1-2 |
| Genie Safe-T-Beam (red light sends, green light receives) | ||
| Both lights steady | Normal | Nothing |
| Red blinks 2 times, green on | Beam blocked or sensors out of line | Clear the beam, clean the lenses, make sure the sensors face each other |
| Red blinks 2 times, green off | A sensor wire is broken or loose | Check the wires; call us if they look fine |
| Red blinks 3 times | The sensor is getting interference | Call us |
| Round light on the opener flashes red | Sensors blocked, out of line, or interference from another pair | Check the sensors as above |
Direct sunlight can blind the receiving sensor. Genie mounts its sending sensor on the sunny side of the door, and says to use only Genie sensors with Genie openers.
From Chamberlain Group support, “Troubleshoot Garage Door Safety Sensors that Are Off or Flicker” and “How to Align” (support.chamberlaingroup.com), and Genie’s owner’s manuals for its wall mount and belt/chain openers (geniecompany.com), checked November 2026.
Garage door sensor alignment and sensor repair
Often a garage door sensor repair is a sensor that was bumped by a bin, a bike or a car. You can usually fix that yourself:
- Clear the beam. Move anything near the sensors and wipe both lenses with a soft dry cloth.
- Align the receiving sensor. On LiftMaster and Chamberlain, loosen the wing nut on the green light sensor, turn it until the green light glows steadily, and tighten it. If it still blinks, do the same on the amber sensor.
- Check the wires. On LiftMaster and Chamberlain, white wires go to the white terminal and white and black striped wires to the grey terminal on the opener. Tug gently to make sure they are seated.
- Test the door. Close it with the remote. Then test the safety reversal (below).
Need to close the door before it is fixed? On LiftMaster and Chamberlain openers, and on Genie, press and hold the wall button until the door is fully closed. Watch the door the whole time.
When to call us
- The lights stay off or keep flickering after you clean and align them: a wire in the wall may be broken or shorted, or a sensor has failed. We test the wiring and replace sensors or wire.
- The sensors are mounted too high. LiftMaster says no higher than 6 inches above the floor; the CPSC says 4 to 6 inches.
- The opener has no sensors at all.
Why the door will not close without them
Federal rules have required automatic residential garage door openers made on or after January 1, 1991 to reverse, and since 1993 to have an external entrapment protection system: an electric eye, a door edge sensor or an equivalent device, under the UL 325 standard. The CPSC urges owners of older openers that do not reverse to replace them, and to inspect the door and opener every 30 days. Never tape over, bypass or remount the sensors high on the wall to make the door close.
Test it monthly. With the door open, close it and wave an object through the beam: the door must stop and go back up. Then lay a 2x4 flat on the floor under the middle of the door and close it: the door must reverse when it touches the board. If it does not, stop using the opener and call us.
From the CPSC safety alert “Non-Reversing Automatic Garage Door Openers Are a Hazard” (Publication 523) and the CPSC 1993 final rule announcement (cpsc.gov), Chamberlain Group support (support.chamberlaingroup.com), and Amarr’s and Overhead Door’s owner maintenance guides, checked November 2026.
Garage door remote programming: LiftMaster, Chamberlain and Genie
Before you start, clear the area under the door: it can move while you program. The full step by step guides are on our LiftMaster remote and keypad programming page and our Genie opener page.
LiftMaster and Chamberlain
Press and release the learn button on the opener (its light comes on). Within 30 seconds, press and hold the remote button until the opener lights flash or you hear two clicks. The color of the learn button tells you which remotes work: white (2025 to now), yellow (2011 to 2025), purple (2005 to 2014), red or orange (1997 to 2005) and green (1993 to 1997).
Genie
Hold the PROGRAM/SET button until the round light turns blue, then let go; the long light flashes purple. Within 30 seconds, stand at least 5 feet away and slowly press the remote button twice. On older Genie openers with a LEARN CODE button, press it once, then press the remote button twice.
Universal garage door remotes
A universal remote works with several brands, but it still has to support your opener’s system. The LiftMaster L992U universal remote works with every LiftMaster and Chamberlain learn button color, green through white. Genie says it can only guarantee Genie brand remotes and keypads on Genie openers. Openers made before 1993 (on LiftMaster, a square learn button) are no longer supported by current remotes; replacing the opener is the fix.
Remote still not working?
- Put in a fresh battery the right way round. Genie remotes take a CR2032 coin cell.
- Wait for the learn light to go out and try again. Holding the learn button too long erases every remote.
- Works only up close? LED bulbs in or near the opener can interfere with the signal.
- Door opening on its own, or a remote lost or stolen? Erase all remotes (on LiftMaster, hold the learn button about 6 seconds until its light goes out) and program the ones you keep.
From Chamberlain Group support articles on programming remotes, learn button colors and remote compatibility (support.chamberlaingroup.com), and Genie’s Programming and Erasing Remote Controls sheet (geniecompany.com), checked November 2026.
Garage door keypad programming and car HomeLink
LiftMaster 877MAX keypad
Hold * and # until the keypad lights stop blinking, enter a 4 digit PIN and press #, press ENTER once for a yellow learn button (twice for purple, three times for red or orange, four times for green), press 0, then press the learn button on the opener and, within 30 seconds, enter your PIN and press ENTER until the opener lights flash. The newer L979 keypads have a QR code on the back that walks you through it on your phone.
Genie wireless keypad
A new Genie keypad comes with the PIN 3-5-7. Put the opener into programming mode, press 3-5-7, then press UP/DOWN slowly 3 to 4 times until the door moves. Change the PIN right away: enter 3-5-7, press PROGRAM, enter a new PIN of 3 to 8 digits and press PROGRAM. Mount the keypad within sight of the door, at least 5 feet above the floor.
HomeLink in your car
Park outside facing the door with a working remote. You hold the remote near the HomeLink button to train it, then finish the pairing; on Genie openers that means putting the opener into programming mode and pressing the HomeLink button. The exact steps depend on the car and the opener. Some cars pair through the dashboard screen, some have the sensor in the bumper, and some need a HomeLink Compatibility Bridge. Genie lists its Pro openers as HomeLink and Car2U compatible with no bridge. For car specific help, HomeLink is at homelink.com or 1-800-355-3515.
Full steps for each: LiftMaster keypads and HomeLink, Genie keypads and HomeLink.
From Chamberlain Group support (“How To Program Or Change The PIN For a 940EV/940EVMC or 877MAX/877MAXMC Keypad”, “HomeLink | Pair Your Vehicle”), Genie’s GK wireless keypad instructions and HomeLink article (support.geniecompany.com), checked November 2026.
What a remote or sensor visit costs
We find the problem first and give you a firm price before any work begins.
| Service | Starting at | Notes |
|---|---|---|
| Service call | $45 | Finding the problem; waived when we do the repair |
| Safety Tune-Up | $149 | See our tune-up page |
| Garage Door Opener Installation | $495 | When the opener is too old for current remotes or has no safety sensors |
| Remotes, keypads, sensors, wiring | Firm price on site | Depends on the opener and the parts it needs |
Starting prices from ADP’s published price list, November 2026.
We offer military and senior discounts, and financing with a quick prequalification. For an opener that hums, will not move or shows an error code, see garage door opener repair.
Remote, keypad and sensor questions
Why does my garage door go down and then back up?
Usually the safety sensors, and Genie says to check them first: something is in the beam, the sensors are out of line, or a wire is damaged. If the sensors are clear and steady, the travel limits, the force setting or the door itself may need attention. See why a garage door won’t close.
Why are my garage door sensors blinking?
On LiftMaster and Chamberlain, a flickering green light means the beam is blocked or the sensors are out of line. On Genie, a red light blinking 2 times means the same; 3 times means interference.
Can I program a new remote without the old one?
Yes. Programming is done at the opener’s learn or program button, not from an old remote. You only need an old remote to train a car’s HomeLink.
Do you program remotes for gates and commercial doors?
Yes. See gate repair and commercial garage door repair.
Garage door remotes, keypads and sensors in Maryland
Call ADP Garage Door Repair for garage door remote programming, keypad and HomeLink setup, or sensor alignment and repair anywhere in Central Maryland. We are open 24/7 including weekends and holidays, you get a firm price before any work begins, and the $45 service call is waived when we do the repair. Guides: program a LiftMaster remote or keypad, LiftMaster blinking light codes, Genie openers, opener troubleshooting and garage door opener repair.
What our customers say
Rated 5.0 stars from 1,266 Google reviews
Our Prices
prices starting from
- Service Call $45 Diagnose a Problem (Waived with Service).
- Safety Tune-Up $149
- Garage Door Opener Installation $495
We offer financing
Prefer to pay over time rather than all at once? Prequalify for financing today.
*All financing is subject to credit approval. Your terms may vary. Payment options through Wisetack are provided by our lending partners. For example, a $5,500 purchase could cost $253.54 per month for 24 months, based on a 9.9% APR, or $1,833.33 per month for 3 months, based on a 0% APR. Offers range from 0 to 35.9% APR based on amount requested and creditworthiness. Not all merchants and lending partners participate in 0% interest programs. Terms range from 3 - 120 months and may vary based on merchant, lending partner, or transaction size. State interest rate caps may apply. No prepaid finance charges or participation fees. See additional terms at wisetack.com/faqs.











